- #Fuzzmeasure user guide pdf how to#
- #Fuzzmeasure user guide pdf drivers#
- #Fuzzmeasure user guide pdf driver#
- #Fuzzmeasure user guide pdf download#
Every piece in the room makes such a difference in the sound of the room. That’s another reason why I like FuzzMeasure. It's fast, and when I have to go into a room with more technical difficulties it saves me time and energy because I may be having to repair old drivers or amps on location and I'm getting less and less time to actually tune. So now I can deal with the issues, and tune and not have to be there all night! When I do a consultation on another room, I may not know what to expect given the limitations of their room, the condition of their components or their speaker drivers, etc.
the 2 seconds with FuzzMeasure… Sometimes I still graph manually with my own tones… but less of a need now. A lot of clients just want you to tune the room fast and FuzzMeasure helps me do it fast… a graph takes 20 minutes or more vs. Why I like FuzzMeasure is because it’s fast. Every piece in a room makes such a difference in the sound of the room. I set expectations given their room and the components of their speakers. What is the studio consultation process like? For example, the new design of the markers is amazing. To be able to zoom in on frequency ranges, track and compare the changes I make in the system is such helpful detail. It’s the small differences that make the world of difference in FuzzMeasure 4. I’m the guy making the speakers and the sources in the room sound as good as they can! As a longtime FuzzMeasure user, what’s exciting about FuzzMeasure 4?
#Fuzzmeasure user guide pdf how to#
And I can usually tell you why and how to improve the room. I’m not the guy designing rooms on a piece of paper, but I can tell you if a room sounds good or not and I can align a speaker system. I’m not a trained acoustician, I’m an audio engineer. I was using a measurement mic playing back Pink Noise then would draw a graph on graph paper, a very analog old technology approach. FuzzMeasure does it so much faster with the sweep, a lot less room for error…. The tuning went fast! My new speaker alignment system is now based around FuzzMeasure.
#Fuzzmeasure user guide pdf download#
The guy I bought ours from suggested I download FuzzMeasure so I downloaded it for the helluva of it. Akon had Augspurger studio monitors and we did too at ZAC. I know you have the floor and wall check boxes in the diffraction tool but that tool doesn't model the curvature of the CBT baffle.How did you get started with FuzzMeasure? It would be so nice to have check boxes to include radiation from adjacent wall, ceiling, floor surfaces.
#Fuzzmeasure user guide pdf driver#
I wonder if you would see fit to support it directly in Vituix as it is a fair amount of work to do it by cut and paste of full array of drivers and then adjust the xyzR of each driver to the new locations. Without it, I might have built and measured a prototype before finding out front radiation was 6 db down. Use of image analysis like this is invaluable. I suppose the -6db that is why rear ports are recommended for vented midranges
At the same time, At the same time, the same -6db would apply to rear port on a vented box, so I hold some slight hope that it might be not be accurate. I believe it is a correct result and the surprise is a reflection on me but I would appreciate your confirmation. More importantly, it showed me that the SPL in front on axis would be 6db down relative to that to the rear, throughout the range, not just at the high end. Inclusion of the image showed me a boundary null at 188 Hz and so is useful for that reason alone. By the image method, this models a wall halfway between which puts the back of the CBT 50mm or so from the wall at its closest (also curved) approach. I needed to include the reflection off the front wall so I included an image array 1200mm behind the real array with the drivers rotated appropriately. I have always heard that bass is omni-directional and so I thought that confined to a low enough range, a rear firing array, chosen for aesthetics, would work well. I modeled it in Vituix and got a surprising answer. I was contemplating the use of a rear firing subwoofer array (100 hz down) on my CBT line array.
0 kommentar(er)
